It is not compatible with the V1 library!
However, if you have code for the older shield, adapting the code to use the new shield isn't difficult. Choose the right motor (and controller) for the job! If you buy less than a full reel, you'll get a single strip, but it will be a cut piece from a reel which may or may not have a connector on it. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements:Instead of using a latch and the Arduino's PWM pins, we have a Comes with an assembled & tested shield, terminal block, plain header, jumper.
All text above must be included in any redistribution. This is the library for the Adafruit Motor Shield V2 for Arduino. Stepper motor - NEMA-17 size - 200 steps/rev, 12V 350mAShield stacking headers for Arduino (R3 Compatible)Small Reduction Stepper Motor - 12VDC 32-Step 1/16 GearingSmall Reduction Stepper Motor - 5VDC 32-Step 1/16 GearingAdafruit DRV8871 DC Motor Driver Breakout Board - 3.6A MaxAdafruit TB6612 1.2A DC/Stepper Motor Driver Breakout BoardAdafruit Motor/Stepper/Servo Shield for Arduino v2 Kit Control your robot via WiFi using Arduino & the CC3000 WiFi chip
N20 DC Motor with Magnetic Encoder - 6V with 1:298 Gear RatioN20 DC Motor with Magnetic Encoder - 6V with 1:150 Gear RatioN20 DC Motor with Magnetic Encoder - 6V with 1:100 Gear RatioN20 DC Motor with Magnetic Encoder - 6V with 1:50 Gear RatioAdafruit 2.13" Monochrome E-Ink Bonnet for Raspberry PiAdafruit SHARP Memory Display Breakout - 2.7" 400x240 MonochromeThe original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. If the piece comes from the end of the reel, the connector may be on the output end of the strip!
Some soldering is required to assemble the headers on. It is Adafruit invests time and resources providing this open source code, please support Adafruit and open-source hardware by purchasing products from Adafruit!Written by Limor Fried/Ladyada for Adafruit Industries. It supports DC …
It supports DC motors & Stepper motors with microstepping as well as stacking-support. It supports DC motors & Stepper motors with microstepping as well as stacking-support. Adafruit NeoPixel Digital RGB LED strips come to us in 4 or 5 meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires as shown in the pic below. Adafruit Motor Shield V2 Library .
This is the library for the Adafruit Motor Shield V2 for Arduino. Stackable, high current DC and Stepper motor shield To use the shield on an Arduino, you'll need to install the Adafruit Motorshield v2 library.
We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. Stacking headers not included, but we sell them in the shop so if you want to stack shields, please pick them up at the same time.
BSD license, check license.txt for more information. GitHub is home to over 50 million developers working together to host and review code, manage projects, and build software together. This library is not compatible with the older AF_Motor library used for v1 shields. “ I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success”
Library for the Adafruit Motor Shield V2 for Arduino. The two 5-pin sets go on either side.
The 2-pin piece goes near the bottom of the shield.
Slide the 3-pin terminal blocks into 2-pin terminal blocks so that you have 2 x 5-pin and 1 x 2-pin blocks. Use Git or checkout with SVN using the web URL. Make sure that the open holes of the terminal blocks face out! If you order a full 4 or 5 meters, you get the full reel with both connectors installed (like the pic below). Adafruit Industries, Unique & fun DIY electronics and kits Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit [v2.3] ID: 1438 - The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better.